Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5692 gości 
Kategorie
Informacje
Polecamy
Strona główna >> PHILIPS >> MX980D Instrukcja Obsługi
 
 0 szt. w koszyku 

PHILIPS MX980D
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis PHILIPS MX980D Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 23 (kliknij aby zobaczyć)
TUNER
Tuning to radio stations
You can search for radio stations by scanning the frequency band. You can also key in the frequency of a known radio station. If an FM station is being broadcast and received in stereo, STEREO is shown. Searching for radio stations 1 Turn SOURCE SELECTOR to select the tuner. yTUNER is displayed. 2 Select a waveband by pressing TUNER BAND repeatedly. yThe selected waveband is displayed. 3 Keep 1 or 2 pressed for approximately 1 second. ySEARCH is displayed and the tuner tunes to a station with sufficient strength. 4 Repeat this procedure until you find the desired station. � To fine tune to a weak transmitter, briefly press 1 or 2 as often as necessary for optimum reception. Tuning to a radio station by frequency (with the remote control only) 1 Press TUNER. yTUNER is displayed. 2 Press FR. D.. y_ is displayed. 3 Use 1�0 to key in the frequency of a radio station. Notes: Only valid numbers within the frequency range of the tuner can be keyed in.

Storing radio stations
You may store up to 30 radio stations in the memory. The receiver can select and program radio stations by itself or you can choose them yourself. Automatic programming 1 Choose * TUNER from the menu and press NEXT 2. 2 Choose AUTO INSTALL and press NEXT 2. yThe preset number where programming will start, the waveband and AUTO are displayed. 3 Turn TUNER PRESET X to change the preset number where programming should start. 4 Use TUNER BAND to switch to the desired waveband. 5 Press ENTER / OK to start programming. yAUTO INSTALL flashes and all available radio stations are programmed, this may take a few minutes. Programming is done when AUTO INSTALL stops flashing. Manual programming 1 Choose * TUNER from the menu and press NEXT 2. 2 Choose MAN INSTALL and press NEXT 2. yA preset number, the waveband and the frequency are displayed. 3 Turn TUNER PRESET X to change to the preset number where the radio station should be stored. 4 Tune to the desired radio station (see �Searching for radio stations�). 5 Press ENTER / OK to confirm your selection. ySTORED is displayed briefly. The radio station is programmed at the chosen preset number. 6 Select and store all desired radio stations this way.

Switching FM sensitivity
You can switch the tuner to a lower search sensitivity, to search only for stations with a strong signal (FM only). 1 Turn SOURCE SELECTOR to select the tuner. yTUNER is displayed. 2 Press SENS. on the receiver. yEither SENS HI or SENS LO is displayed for 5 seconds. Note: While searching for radio stations, the actual sensitivity is displayed. In this case, SENS LO means the tuner is looking only for radio stations with a strong signal.

23

English

Klienci kupując ten produkt kupili także

$4.99

MX980D PHILIPS
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.153 - Number of Queries: 98 - Query Time: 0.037